阳江附近想过夜电话联系

Guosheng machinery > Product Center > Feeder equipment >
 Disc feeder

Disc feeder

Hot sale

[feed size]: ≤50mm

[production capacity]: ≤100m³h

[application scope]: Suitable for coal preparation, mineral processing, sintering, power, building materials and other industries

[product introduction]: Disc feeder is actually a quantitative feeding equipment, which can evenly send materials to the next equipment, which not only saves labor, but also avoids the damage to the equipment caused by the sudden increase or decrease of feeding materials, so as to extend the service life of the whole production line equipment to a certain extent

Sales Hotline: 0373-5419909

Product introduction

In fact, the disc feeder is a kind of quantitative feeding equipment. It can deliver materials evenly to the next equipment, which not only saves labor, but also avoids the damage of the equipment caused by excessive or insufficient feeding, To a certain extent, the service life of the whole production line is extended. In terms of appearance, the disc feeder can be divided into br closed type and Kr open type. No matter which type of equipment, the feeding capacity is relatively large, It is especially suitable for conveying those powder materials and non viscous materials with poor fluidity, especially for coal preparation, mineral processing, sintering, electric power, building materials and other industries.
 
 Disc feeder

Product features

1. The structure of the equipment is simple, but the feeding amount is large, which can meet the needs of customers to a large extent, and the operation is particularly reliable, and the adjustment and installation work is relatively convenient.
2. The finite moment hydraulic coupling is installed inside the equipment, which can start overload protection with full load and bear large bin pressure, so it is the first choice for feeding process.
3. The feeding speed is uniform, and there is almost no material accumulation in the whole feeding process. In addition to the sticky materials and the materials with good fluidity, other powder, granular or small particle materials are not easy to be fed Yes.
4. It adopts the advanced plane double enveloping toroidal mule bar reducer, which has large load capacity and high transmission efficiency.
5. If the coal material is delivered, the maximum feeding amount can reach 1200 T / h.
6. The lining plate is composed of small pieces of wear-resistant steel plate, which is not only light and easy to replace, but also can be targeted to replace the worn lining plate according to the actual wear situation, so as to make rational use of materials and reduce the maintenance cost.
 
 Working principle of disc feeder

working principle

The motor of the disc feeder drives the reducer to run through the rotation of the belt, which makes the disc rotate uniformly around one side. After the material enters the lining plate on the disc, it will rotate with the disc When the material is transferred to a certain position, the material will be scraped out by the scraper on the lining plate and enter the next process to achieve the purpose of feeding.
The disc feeder is composed of driving device, feeder body, belt conveyor for metering and metering device. The disc feeder and belt conveyor are driven by a set of driving device, and the electromagnetic clutch device of the driving device It has the function of starting, stopping and function conversion of feeder.
 
 Disc feeder model

technical parameter

Model and specification BR1000 BR1500 BR2000 KR1000 KR1500 KR2000
Disc diameter mm one thousand one thousand and five hundred two thousand one thousand one thousand and five hundred two thousand
Disc speed r / min six point three six point three four point seven nine seven point five seven point five seven point five
Maximum material size mm <50 <50 <50 <50 <50 <50
Feeding capacity m 3 / h thirteen thirty eighty fourteen twenty-five one hundred
Motor AC drive Y132S-6 Y160M-6 Y160L-6 Y112M-6 Y132M2-6 Y160L-6
three seven point five eleven two point two five point five eleven
three hundred and eighty three hundred and eighty three hundred and eighty three hundred and eighty three hundred and eighty three hundred and eighty
nine hundred and forty nine hundred and seventy nine hundred and seventy nine hundred and forty nine hundred and sixty nine hundred and seventy
DC drive Z2-51 Z2-62 Z2-72 Z2-42 Z2-61 Z2-72
three seven point five thirteen two point two three point five thirteen
two hundred and twenty two hundred and twenty two hundred and twenty two hundred and twenty two hundred and twenty two hundred and twenty
250-1000 250-1000 250-1000 250-1000 250-1000 250-1000
Reducer model ZS50-3 ZS75-3 ZS-82.5 JZQ350-Ⅲ JZQ400-Ⅲ JZQ500-Ⅲ
speed ratio sixty-three sixty-three eighty-seven thirty-one point five thirty-one point five thirty-one point five

matters needing attention

1. When the equipment is delivered, most of them are delivered as a whole machine. Therefore, when the equipment arrives at the operation site, it is necessary to check carefully to avoid missing parts on the delivery route.
2. When unloading, the steel wire rope is usually used for lifting and unloading. It is forbidden to use the steel wire rope to tie the disc for lifting, so as to avoid damaging the disc. The whole machine with the frame should be tied to lift and unload.
3. In case of disassembly delivery, all accessories shall be installed according to the drawing size of accessories provided by the manufacturer after reaching the operation site, and anchor bolts shall be set for fastening equipment if necessary.
4. During the installation, especially the center of the silo, the deviation of the center distance should not exceed 5mm to avoid affecting the feeding effect.
5. The channel steel column under the disc shall be fastened in place, and the disc must be placed horizontally without any inclination, and the deviation value shall not be greater than 0.5 ‰.
 
 Br closed disc feeder

 
 Precautions for disc feeder

Maintenance

1. It is necessary to ensure that the wear-resistant lining plate of the feeding disc is firmly fastened without any looseness. If the wear is serious, a new replacement should be replaced in time to avoid greater equipment failure.
2. The lubricating grease is necessary for all rotating parts of the equipment. It is necessary to ensure good lubrication. The parts with oil cup should ensure the oil quantity is moderate and there is no lack of oil.
3. The lifting and adjusting device of the equipment is a very important part, which should be complete and complete. The adjusting screw rod should rotate flexibly and freely, especially the joint with the expansion cylinder of the tank body should be firm and not loose There shall be no defects with gaps.
4. If the material is fed for a long time, the screw guide plate of the equipment will inevitably be worn. However, the wear clearance shall not exceed 10 mm. Once the wear clearance is exceeded, the feeding quality will be affected.
5. The guide scraper plays an important role in the equipment. Daily maintenance should be strengthened, and the disc should be firmly connected. If the guide plate with arc, the arc rake teeth should also be fixed in place with the disc, so the wear is serious Any shortage or deformation should be replaced in time.
6. At the discharge end of the equipment, there will be a discharge scraper. In the installation process, the angle size should meet the process requirements, and the maximum plane clearance with the disc should not exceed 12mm.
 
 Daily maintenance of disc feeder

Customer case

  Heavy duty motor dzsf high efficiency vibrating screen
Heavy duty motor dzsf high efficiency vibrating screen

Processing materials:

throughput:

Equipment configuration: One dzsf1850-3p vibrating screen and three TD75 belt conveyors

View details
 Herringbone nylon antiskid belt conveyor
Herringbone nylon antiskid belt conveyor

Processing materials: resin

throughput: 15t/h

Equipment configuration: Six herringbone nylon antiskid belt conveyor

View details

Recommended products



Xinxiang Guosheng Machinery Equipment Co., Ltd Yu ICP Bei 14028944-2 Address: west exit of Xinxiang Changji Expressway

Online consultation
Ask for a quotation
Sales Hotline

Sales Hotline: 13569819530